Station Video Mux: Difference between revisions

From YSTV History Wiki
Jump to navigation Jump to search
(Controller PIC been replaced)
(→‎32 x 4 replacement: I've just found the data on the tuners on distel's site still!)
Line 16: Line 16:
An increase was made to 32 inputs and 4 outputs, along with controller box.
An increase was made to 32 inputs and 4 outputs, along with controller box.


It included two NICAM stereo terrestrial tuners from [http://www.distel.co.uk/ Display Electronics] which could be retuned under computer control, this was key to the scheduling system and was also intended to make use of the recently upgraded AV network which was stereo capable.
It included two [http://www.distel.co.uk/data_my00.htm NICAM stereo terrestrial tuners] from [http://www.distel.co.uk/ Display Electronics] which could be retuned under computer control, this was key to the scheduling system and was also intended to make use of the recently upgraded AV network which was stereo capable.


The new mux was briefly installed for a weekend for testing in {{unsure|2002}} and later withdrawn for minor hardware alterations - it was carried back to Cambridge by train, which included a brief section sliding round in the back of a coach as a derailment had meant trains had to skip part of the journey to Peterborough, making it the most travelled mux in history.
The new mux was briefly installed for a weekend for testing in {{unsure|2002}} and later withdrawn for minor hardware alterations - it was carried back to Cambridge by train, which included a brief section sliding round in the back of a coach as a derailment had meant trains had to skip part of the journey to Peterborough, making it the most travelled mux in history.
Line 22: Line 22:
All the parts were sourced as free samples from [http://www.maxim-ic.com/ Maxim] under various psuedonyms since the MAX458 crosspoints were actually worth about £40 each.
All the parts were sourced as free samples from [http://www.maxim-ic.com/ Maxim] under various psuedonyms since the MAX458 crosspoints were actually worth about £40 each.


To avoid the obsolescence problem that the Breaker 88 unit suffered, there are infact two muxes. A spare circuit board and set of 4 chips are in storage incase of failure, and the controller is made using a cheap reprogrammable microcontroller. Some 885 lines of assembler code are all that is required in the micro to perform all of its control functions.
To avoid the obsolescence problem that the Breaker 88 unit suffered, there are in fact two muxes. A spare circuit board and set of 4 chips are in storage in case of failure, and the controller is made using a cheap reprogrammable micro controller. Some 885 lines of assembler code are all that were required in the micro to perform all of its control functions.


==Today==
==Today==

Revision as of 19:10, 24 May 2007

Breaker 88

The mammouth broadcast of Breaker 88 was responsible for several new pieces of YSTV equipment being designed and built, a sync pulse generator (SPG) in a 2U rack, and a video multiplexor.

The video mux had 4 buses: Auxilliary, Tape, Record, Network. By the mid 1990's various bits of the original circuitry had failed and no replacement parts were obtainable, so the mux had some rotting limbs amputated to reduce it to only 3 buses. A separate 1U mux switched network video under the control of BBC Schedula.

Motivation to design a new video mux was severalfold:

  • Only 3 terrestrial tuners remained from the original Rediffusion system, these had to be manually changed over by the Scheduling Manager to match the schedule depending on which of the 5 terrestrial channels were required, and some of these buttons were jammed too
  • An explosion of video equipment within the larger G/046 station meant all of the remaining working inputs were now in use
  • The black controller box would 'crash' occasionally when the state machine inside made out of logic chips got stuck
  • A desire to simplify the video setup so that any video source could be routed to and from anywhere

32 x 4 replacement

A replacement mux was first explored in 1997 by Rob Sprowson, though not built straight away due to other pressing projects and budget constraints. Instead the parts were accumulated slowly and design work done during the university holidays. Finally in April 2001 the new layout was sent off to be made, and finally the parts could be pieced together.

The backpanel wiring diagram

An increase was made to 32 inputs and 4 outputs, along with controller box.

It included two NICAM stereo terrestrial tuners from Display Electronics which could be retuned under computer control, this was key to the scheduling system and was also intended to make use of the recently upgraded AV network which was stereo capable.

The new mux was briefly installed for a weekend for testing in 2002Unverified or incomplete information and later withdrawn for minor hardware alterations - it was carried back to Cambridge by train, which included a brief section sliding round in the back of a coach as a derailment had meant trains had to skip part of the journey to Peterborough, making it the most travelled mux in history.

All the parts were sourced as free samples from Maxim under various psuedonyms since the MAX458 crosspoints were actually worth about £40 each.

To avoid the obsolescence problem that the Breaker 88 unit suffered, there are in fact two muxes. A spare circuit board and set of 4 chips are in storage in case of failure, and the controller is made using a cheap reprogrammable micro controller. Some 885 lines of assembler code are all that were required in the micro to perform all of its control functions.

Today

The outputs originally drove 8 copies of each bus to avoid the need for seperate distribution amplifiers, however in a heavily loaded system some crosstalk was observed. This was misdiagnosed as due to electric fields (!) and the integrated amplifiers chopped out, despite the MAX497 buffers being socketted. It is believed simply increasing the decoupling to the power supply would have resolved the problem and left the unit at its full specification.

In 2006 the original PIC within the controller was replaced with a PIC18F2455. This was the first step towards giving Spider and SchedSeven control of the Mux, although currently the USB side of the firmware is still under development.